This is a generic type oil containing molybdenum Effective for long-term lubrication and seizure-prevention in bearings and gears, and prevention of wear and stick-slip in sliding surfaces of various machines.This is a general-purpose organic molybdenum oil.This is a non-black oil that can be used for the same purpose as the MS Oil.Contains a high concentration of organic molybdenum and can be used in areas where black residue is undesirable.This is a versatile lubricating oil with excellent lubrication, wear resistance, and rust prevention.Ideal for sliding surfaces of various machines.This is a versatile oil made by dispersing PTFE in a high-performance synthetic oil.It has little effect on resin and is almost colorless and odorless.Metal parts such as chains and gears will gradually wear out if they are not oiled. Rust and breakage may occur from the worn parts, leading to unexpected accidents.Mineral oilMolybdenumdisulfide (MoS2)Grayishblack68.3mm2/s105Mineral oilOrganicmolybdenum Light yellowgreen80.3mm2/s96Mineral oilOrganicmolybdenum Light yellowgreen150.8mm2/s96Mineral oilOrganicmolybdenumGreen150.8mm2/s96MilkywhiteThere are various ways to supply lubricant, and it is necessary to select a method depending on the application. Here are some common lubricating methods.NICHIMOLY oil products are high-quality lubricants made by stably dispersing ultrafine particles of molybdenum disulfide (MoS2), organic molybdenum, and fluororesin powder in high-grade oils. We offers a wide range of oil products for general purpose, gear, chain, and high temperature applications.◆Viscosity indexThe viscosity index is a measure of a fluid’s change in viscosity relative to temperature change. The higher the viscosity index of an oil, the less the viscosity is affected by changes in temperature. ◆Flash pointThe flash point is the temperature at which the vapor of a flammable liquid reaches the concentration required for combustion. On the other hand, the ignition point is the temperature at which a combustible substance ignites or explodes without an ignition source when heated in air.◆Pour pointThe pour point is an indicator of an oil’s flowability at a low temperature. If the temperature of an oil is lower than the pour point, it will solidify. Fueling MethodNICHIMOLY Oil ProductsKinematicviscosity (40˚C)Viscosity indexAdvantages・Easy・Low initial cost・Saves manpower compared to manual feeding・Inexpensive because the oil can be used repeatedly・Fixed quantity controlled by machineAppearanceDisadvantages・Requires frequent lubrication・Possibility of foreign matter contamination・Viscosity of oil changes with temperature・Requires management of oil volume and temperature・High initial costFlash pointPour point52˚C-40˚CRusted gears and chainsCharacteristics/ApplicationsPack SizeLubricatingmethodDescriptionManual feedlubricationManual lubrication method using oil filler, etc.Drip-feedlubricationA drip-feed lubricator is used to drip lubricant little by little onto the part to be lubricated.A method of immersing chains or gears in oil, which is used for reducer gears.Oil bathlubricationCentralizedlubricationAutomatic lubricating method using a dedicated lubrication deviceProduct nameMain ingredientsSynthetic oilPTFE18L4L×418L4L×418L18L4L×418LMS Oil 20MP-40S OilMP-40 OilLAP OilAPPLUBE Oil240˚C-17.5˚C236˚C-22.5˚C210˚C-17.5˚C210˚C-17.5˚C7mm2/s−General-purpose oil18Explanation of Basic Oil Terminology◆Kinematic viscosityKinematic viscosity is the viscosity of a fluid divided by the density of the fluid under the same conditions (temperature, pressure). It is measured in stokes (St){cm2/s} or centistokes (cSt){mm2/s}. [1 cSt = 1 mm2/s]*Viscosity refers to the internal resistance of a fluid which is indicated by the magnitude of shear stress in a unit area in the direction of velocity in a plane perpendicular to the direction of the shear velocity when there is a shear velocity (shear rate) in the fluid. Measured in poises (P){10-1 Pa·s} or centipoises (cP)(mPa·s).Oil
元のページ ../index.html#19